参数对照(39 项)
下表即转换引擎执行的翻译映射;同名键直接透传,不占行。
取值换算
| Anycubic 参数 | Bambu Studio 取值 |
|---|---|
| ensure_vertical_shell_thickness | ensure_all → enabled · ensure_moderate → enabled · none → disabled |
| internal_solid_infill_pattern | rectilinear → zig-zag |
| ironing_pattern | rectilinear → zig-zag |
| support_ironing_pattern | rectilinear → zig-zag |
| gcode_flavor | klipper → marlin |
| tree_support_wall_count | 0 → -1 |
目标工程基准
| 项 | 值 |
|---|---|
| 打印机预设 | Bambu Lab P1S 0.4 nozzle |
| 工艺族 | @BBL X1C |
| 耗材兜底 | Bambu PLA Basic @BBL P1S 0.4 nozzle |
| Studio 版本 | 02.08.02.61 |
- Anycubic 多机型多对一收敛到拓竹 P1S 基准;文件在拓竹端打开后再按需切你的机型
G-code 接管
| 处理 | 说明 |
|---|---|
- 起止/换料/延时摄影等 5 类 G-code 整族替换为拓竹预设——Anycubic 私有宏在拓竹固件上无效
Bambu Studio → PrusaSlicer 键名对照
| Bambu Studio | PrusaSlicer |
|---|---|
| wall_loops | perimeters |
| sparse_infill_density | fill_density |
| sparse_infill_pattern | fill_pattern |
| top_surface_pattern | top_fill_pattern |
| bottom_surface_pattern | bottom_fill_pattern |
| initial_layer_print_height | first_layer_height |
| initial_layer_speed | first_layer_speed |
| initial_layer_infill_speed | first_layer_infill_speed |
| top_shell_layers | top_solid_layers |
| bottom_shell_layers | bottom_solid_layers |
| top_shell_thickness | top_solid_min_thickness |
| bottom_shell_thickness | bottom_solid_min_thickness |
| outer_wall_speed | external_perimeter_speed |
| inner_wall_speed | perimeter_speed |
| internal_solid_infill_speed | solid_infill_speed |
| top_surface_speed | top_solid_infill_speed |
| sparse_infill_speed | infill_speed |
| enable_support | support_material |
| nozzle_temperature_initial_layer | first_layer_temperature |
| bed_temperature_initial_layer | first_layer_bed_temperature |
| wall_generator | perimeter_generator |
| printable_area | bed_shape |
| enable_ironing | ironing |
| layer_change_gcode | layer_gcode |
| before_layer_change_gcode | before_layer_gcode |
取值换算
| 参数 | Bambu Studio 值 → PrusaSlicer 值 |
|---|---|
| support_material_style | |
| ironing_type | no ironing → top · all → solid |
| top_fill_pattern | monotonicline → monotoniclines |
| bottom_fill_pattern | monotonicline → monotoniclines |
- support_material_style 由支撑类型推导:auto/manual→grid(普通),tree→organic(树状)
常见问题
转换后还要在 PrusaSlicer 里调什么?
建议核对:打印机与喷嘴预设是否选对(转换器不替你选机器)、首层与悬垂处支撑、多色工程槽位顺序。
多色槽位会保留吗?
会。多色工程的耗材槽位顺序被保留并映射到目标的槽位/工具体系;单色工程不受影响。
打印机/工艺预设会一起过去吗?
Anycubic 多机型工程会收敛到拓竹 P1S 基准(多对一);在拓竹端打开后再切换到你的机型,工艺参数仍在。